Aprilaire 8554 Instrukcja Użytkownika Strona 1

Owner’s Manual MODEL 85545-2 Day Programmable ThermostatELECTRONIC THERMOSTAT®110-792B 7/12/01 8:28 AM Page 1

Step 1: Press and release the MODE button until the word “HEAT” andthe “ ” heating symbolappear on the display.Step 2: Press andrelease the PROGRAM bu

– 9 –Step 5: Press the DECREASE button or INCREASE button to set the desired minutes for the Morning “”event (program starting times are

Step 11: Repeat steps 2-6 to complete programming for the Evening “ ” event.Step 12: Press and release the PROGRAM button – the Night “ ” event

Setting Or Changing Cooling TemperaturesNOTE: Cooling temperatures must be set at least 2 degrees higher than heating temperatures. (Example: If heati

– 12 –Step 2: Press and release the PROGRAM button – “Mo TuWe Th Fr”; Morning“ ” event symbol; and flashingstarting time you programmed w

– 13 –Step 7: Press and release the PROGRAM button until the temperature for the Morning “ ” event flashes. Repeat steps 2-4 for the Morning “

– 14 –For Best PerformanceThe Aprilaire Model 8554 thermostat is designed for accurate temperature control and easy operation. The following guideline

– 15 –Aprilaire Model 85547 Day Programmable Thermostat110-792B 7/12/01 8:28 AM Page 17

TEMPERATURE CONTROL• Reading the Actual Room Temperature: The Model 8554 normally displays the room temperature, not the set-point temperature. • Chec

– 17 –• Returning to Programmed Operation: At any time, press the RESUME button to return the thermostat to operate as programmed.• Change Between °C

OWNER’S MANUAL – TABLE OF CONTENTSENERGY STAR®Program Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 18 –EQUIPMENT CONTROL• Turning on the Fan: At any time the system fan can run continuously by pressing the FAN button. Note that a Fan icon, “

display, which flickers when the heat pump is running. Your thermostat will automatically turn onand off any additional stages of heating as required.

– 20 –can still be programmed, the optional outdoor temperature sensor will work and the heat pump fan will turn on if the FAN button is pressed. To a

After accessing a balance point, it can be changed by pressing the DECREASE button or INCREASE button. This should only be done after consul

– 22 –The DIP switches can however be changed to customize the thermostat’s operation to your particularneeds. This should only be done after consulti

– 23 –If the thermostat does not respond when a button is pushed it may be because the keypad hasbeen locked. A Lock icon “ “ will appear when

To change the DIP switch settings, the thermostat must beremoved from the base which is attached to the wall. The power to the thermostat must be turn

Figure 2Figure 3d) Gently push in and pry up on the handle of thescrewdriver until the lock tab disengages from thecatch tab (you should feel or hear

Once the thermostat panel has been opened and removed from the base, turn the thermostat over and locate the DIP switches found on the circuit board a

Figure 4b) Align the hinge tabs on the base andthermostat panel. Swing the panel to thebase and snap in place at bottom ofthermostat panel (see Figure

– 1 –ENERGY STAR®Program InformationAbout half of all energy used by households goes to heating and cooling the home. By selecting a programmable Apri

– 28 –In Case Of Power FailureThe Model 8554 thermostat does not require a battery. If the power goes out the letters “AC” appear onthe display indica

– 29 –Limited WarrantyYour Research Products Corporation Aprilaire®Thermostat unit is expressly warranted for two (2) years from date ofinstallation t

B2202155 REV. 04/01 110-792BP.O. BOX 1467 • MADISON, WI 53701-1467Products For Better Indoor Air Quality™The Aprilaire®Total Indoor Air Comfort Sys

– 2 –TIME SCHEDULETHERMOSTAT DESIRED EVENT SYMBOL TEMPERATURE Mon Tue Wed Thu Fri Sat SunSETTINGMorning Heat = 70˚ 6:00 6:00 6:00 6:00 6:00 6:00 6:00

– 3 –IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLYProgramming your Aprilaire Thermostat is done in three easy steps: setting the clock, setting the even

– 4 –Step 3: Press the CLOCK button again and “12:” (hours)and “AM” or “PM” will flash. Use the DECREASE or INCREASE button to change the flashing s

Setting Or Changing The Program Programming your AprilaireElectronic Thermostat involves selecting the temperature you want in yourhome and selecting

– 6 –To activate the progressive recovery mode simultaneously press thePROGRAM and FAN buttons. A smallthermostat icon, “ “, will appearunder

– 7 –PROGRAM SCHEDULETIME SCHEDULETHERMOSTAT DESIRED MONDAY – SATURDAY & EVENT SYMBOL TEMPERATURE FRIDAY SUNDAYSETTINGMorning Heat =Cool =Day H